Santa Clarita Roof Pros provides professional metal roofing in Santa Clarita, CA for residential and commercial properties across the Santa Clarita Valley. Metal satisfies both halves of the problem at once, which is why we recommend it on the hillside edges of this valley more often than the volume figures would suggest. It is non-combustible, and a concealed-clip panel is mechanically held rather than glued down.
Standing seam is the version worth paying for. A 24-gauge steel panel in a Kynar 500 finish, on concealed clips over a rated deck and self-adhering underlayment, gives a covering with no exposed fasteners for embers or ultraviolet to work on, a tested uplift rating you can look up, and a service life that outlasts two asphalt roofs. You can look that number up rather than take our word for it.
On a lot backing onto chaparral that combination is hard to beat at any price. We are equally direct about where it does not pay. Standing seam on a complicated tract roof with six hips, three dormers and a chimney is a great deal of hand-formed flashing, and the price reflects every one of those transitions rather than the square footage. Square footage is the wrong way to price a cut-up roof in this material.
On that house the better spend is usually a heavy laminated shingle assembly done properly, with the difference going into the eave, the vents and the perimeter fastening. We would rather sell the shingle job and the detailing than the metal job and no detailing. Exposed-fastener panels have a real place too: detached garages, workshops, barns out toward Agua Dulce, patio covers and additions. That is a genuine trade and we will show you both numbers.
Those cost a fraction of standing seam and they are still non-combustible. The catch is honest maintenance, because neoprene washers dry out in this ultraviolet. Plan on walking the panels and re-torquing screws around the eight-year mark, and expect to replace washers rather than pretend they last as long as the steel does. Budget for that once and the panels will still outlive two shingle roofs.
Two details decide whether a metal roof performs the way its rating claims. Thermal movement has to be allowed for, so clips must float and penetrations need slotted or floating curbs, or the panel oil-cans and fasteners work loose. And closures at eave, ridge and rake must be foam or metal rather than sealant alone, because sealant is the gap embers find. We do not install unpainted galvanised on a house here.
Our licensed and insured team brings the right materials and equipment to every job — Class A rated roof assemblies tested to ASTM E108, listed ember-resistant attic vents with eighth-inch corrosion-resistant mesh, ASTM D7158 Class H wind-rated laminated shingles, 24-gauge Kynar 500 standing seam panels on concealed clips, two-ply SBS modified bitumen with mineral-surfaced cap sheet, mechanical tile clips and screws at eave, rake, hip and ridge — and backs the work with a written workmanship warranty. We serve Santa Clarita and nearby communities including Castaic, Stevenson Ranch, Val Verde, Agua Dulce.
What We Handle
Everything our metal roofing in Santa Clarita covers
One crew, one point of contact, and the full range of metal roofing work in Santa Clarita, CA. If it is on this list we do it in house rather than handing it to a subcontractor:
- metal roofing Santa Clarita
- standing seam metal roof
- 24 gauge Kynar panels
- concealed clip metal roof
- exposed fastener metal panels
- metal roof over hillside lot
- non combustible roof covering
- metal roof wind uplift rating
- snap lock standing seam
- metal roofing cost Santa Clarita
- metal patio cover roofing
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Santa Clarita services.
Materials, equipment and how we do metal roofing
The difference between metal roofing that lasts and metal roofing that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with Class A rated roof assemblies tested to ASTM E108, listed ember-resistant attic vents with eighth-inch corrosion-resistant mesh, ASTM D7158 Class H wind-rated laminated shingles, 24-gauge Kynar 500 standing seam panels on concealed clips, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Santa Clarita job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. Years of roofing work in the Santa Clarita Valley means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do metal roofing outside Santa Clarita
Santa Clarita Roof Pros covers Santa Clarita and the surrounding communities of the Santa Clarita Valley. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Metal Roofing in Castaic, CA — Los Angeles County, population 18,937
- Metal Roofing in Stevenson Ranch, CA — Los Angeles County, population 20,178
- Metal Roofing in Val Verde, CA — Los Angeles County, population 2,399
- Metal Roofing in Agua Dulce, CA — Los Angeles County, population 3,451
- Metal Roofing in Acton, CA — Los Angeles County, population 7,431
- Metal Roofing in San Fernando, CA — Los Angeles County, population 23,946
Start on the Santa Clarita Roof Pros homepage for a free estimate, or call (844) 511-2320 and describe the job.
Why Santa Clarita Chooses Santa Clarita Roof Pros
- ✓Every proposal names a fire rating for the whole assembly and a wind rating for the covering, not one or the other
- ✓We quote listed ember-resistant vents by their tested free area rather than by the size of the hole they cover
- ✓Six fasteners per shingle through the first three courses at every rake and eave, and edge metal at four inches on center
- ✓Tile perimeters mechanically clipped at eave courses, rakes, hips and ridge on any slope with real exposure
The standards behind metal roofing
Quality here is not a matter of opinion — it is written down. The metal roofing work we do in Santa Clarita follows published industry standards: NRCA publishes the Roofing Manual, the industry's reference for details and slope minimums, and Asphalt Roofing Manufacturers Association sets the shingle application and ventilation guidance the warranties reference. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every metal roofing project in Santa Clarita gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (844) 511-2320 for a free metal roofing free estimate in Santa Clarita, or request a quote and we'll get right back to you.